Syvecs Engine Management Kit: Nissan R35 GT-R 2009+

Syvecs

Syvecs Engine Management Kit: Nissan R35 GT-R 2009+

$6,499.00
$6,499.00
$6,499.00
Sold Out

Details

This is the world’s first stand-alone Engine Management Solution for the Nissan R35GTR. Over the last 12 months SYVECS has been working hard to develop a completely new product for the tuning of the Nissan R35GTR. Around the world, as the limits of the VR38DETT are pushed further and further, the last hurdle to jump has always been the OEM ECU. Now free of the restrictions that re-flashing of the stock ECU imposes, tuners can now use the SYVECS EMS to go further, push harder and take advantage of the superior control, Motorsport developed strategies and full data logging that it offers. The advanced engine management, together with a full software suite, offers unbeatable flexibility and protection to all tuning levels, safeguarding your investment, while maximizing performance. 

Standard Features Include: 
Live Tuning of every aspect of the engine’s calibration, including signals sent to the TCM and 4WD 
Adjustable Shift rpm and Speed lockout 
Ability to select desired engine map, boost level, traction and launch control levels through steering wheel buttons 
Fully adjustable Launch control with Anti-lag strategies and Ramp in Maps 
Full Variable Valve Timing control 
Flex Fuel control 
Fully functional with every other Ecu on the Car 
Closed loop Dual Lambda Control 
Fully adjustable closed loop boost control with launch level adjustments and trims for turbo speed, air charge, engine coolant temp, exhaust gas temperatures etc 
Monitor and trimming of exhaust gas temperatures 
Built in data logging using a market leading analysis software of up to 8 hours, with data rates at up to 1000hz 
Rolling Antilag / Pit lane limiter strategies, great for building boost on a roll 
Antitheft and valet modes 
Super fast connection via RJ45 Ethernet port for live tuning anywhere in the world or evenremotely if on track if connected to a wireless unit. 
Adjustable traction control strategies based on lateral g, steering angle and/or individual wheel speed monitoring. 
4 programmable and selectable target slip maps. An immediate torque reduction can be applied by the ECU via ignition retard or a fuel cut. 
Configurable Engine Safety Trips on all important parameters like oil temperature, oil pressure. 
Fuel pump control of both main, and sub pumps, as well as Relative fuel pressure monitoring and limiting in the event of fuel pressure dropping on boost. 
4 different Pedal to Throttle Angle maps with multipliers for different parameters e.g. speed. Again adjustable via steering wheel buttons 
Configurable individual cylinder closed loop knock control, to suit any cylinder modification with adjustments to frequency, windows for listening and gains for each cylinder. Ability to trigger full cylinder shutdown in severe knock conditions. 
Ability to change torque levels or demand levels sent to 4wd unit and TCM ECU for changing of up shift and down shift points, clutch pressures and diff tightness. 
Change torque reduction levels on shifts. Essential for very high power GTRs where themaximum reduction available via the stock ECU is not enough to prevent damage to components 
Ability to change Torque ramp in after launch 
Change throttle blip requests to match your torque band. Especially useful on oversized turbo installations. 
Run up to 7bar map sensors 
Control high or low impendence injectors 
Control up to 12 injectors for high power installations where staged injection may be required 
Change injector dead times based on voltage levels for proper control 
Change injector end angle to ensure injection point is properly calibrated 
Ability to fit any type of external sensor to monitor and trigger safety trips from anything from crank case pressure to damper position 
Ability to use any size DBW throttle body e.g. Chevrolet LS7 
Wet and Dry – Wet and Dry nitrous control with ability to drive solenoids directly and control n20 heaters via pressure monitoring 
Ability to control any external vehicle features based on sensor inputs e.g. Adjustable rear wing linked to G force or exhaust control valves 
Connect any race series dash or even one of our partners’ Touchscreen CANBUS adjustment /display units 
View any input live with built in scope up to 1000hz 

The Full plug and Play kit includes 2 Lab Grade NTK Wideband Lambda Sensors with a 2.5m loom, A Syvecs S8 ECU and a Loom adaptor. We specify superior Lambda sensors to improve accuracy in calibration control, as standard equipment sensors can be affected by exhaust temperature.